服务热线:021-56830399
服务类型
联系我们

滚塑脱模剂销售电话:021-56830399

橡胶脱模剂销售传真:021-56830397

皮带脱模剂销售专员:Jordan 秦先生

轮胎脱模剂销售手机:13611954539

胶管脱模剂销售阿里:bestfluoro

工业皮带脱模剂销售电邮:qin@bestfluoro.com

橡胶脱模剂销售Q Q:  1258506600

脱模剂销售微信二维码




TraSys滚塑脱模剂您现在的位置: 首页 > 产品中心 > TraSys滚塑脱模剂
滚塑脱模剂TraSys715
滚塑脱模剂TraSys715 TraSys® 715 Mold Release Agent TraSys®715 脱模涂层是半透明,水溶性,用于滚塑成型。当施加到模具上,它表现出突出的释放和防粘性,并具有很低的摩擦系数。它是干净的,非油性,不沾污漬,化学惰性的,并且可以在 260℃(500°F)温度或更高的環境下發揮功能。TraSys®715 满足模具生产商對於环境和安全要求。在不使用硅油的情況下,它提供最佳的润滑性和耐久性的组合,發揮一致的释放和减少模具堆积。TraSys®715 是不含溶剂,符合所有现有的和预期的环境法规。此外,

Product Description
TraSys® 715 mold release coating is a translucent water-based dispersion for rotational molding applications.When applied to a mold, it exhibits outstanding release or antistick properties and has a very low coefficient of friction. It is clean, nonoily, nonstaining,
chemically inert, and can function in temperatures to 260°C (500°F) or higher.
TraSys® 715 will meet molders’ production, environmental, and safety requirements. It offers an unmatched combination of lubricity and durability, without the use of silicone oils, providing consistent release and reducing mold buildup. TraSys® 715 is solvent-free, meeting all existing and anticipated environmental regulations. Additionally, TraSys® 715 contains no alcohols that may form flammable vapors.
Uses
TraSys® 715 is ideal for rotational mold internals and other molding applications where a consistent, controlled release is desired.
Direction for Use

TraSys® 715 must be agitated before use. TraSys® 715 mold release coating should be applied to clean and dry surfaces. For maximum results, preheat the mold surface to 55–60°C (130–140°F) before application.

Recommended Procedure
1. Clean mold thoroughly, using glass or plastic bead media, abrasive pads, and cleaning solvent or high pH detergent, to remove all prior mold release
and other sources of contamination.
2. If spraying, use spray equipment that provides a fine mist. When wiping, lightly dampen a clean cloth with TraSys® 715 after agitation. After agitation, apply lightly to the mold’s surfaces, making certain that all areas of the mold are entirely coated.
3. A minimum inner mold temperature of 132°C (270°F) is recommended to cure the release. This can easily be accomplished after application by running the mold empty through a full production cycle with the oven temperature at 170°C (350°F).
Proper curing will give a bond between mold and coating that will ensure no transfer of coating to the first molded part, as well as ensure the most effective coating for durability and cycle life.
4. When spot touch-ups are applied, curing the freshly coated area with a heat gun will further enhance the bond between the coating and the mold’s surface. Larger applications may require a bake cycle as described above.


产品描述
TraSys®715脱模涂料是一种半透明的水性分散体,适用于旋转模塑应用。当应用于模具时,它具有出色的脱模性或抗粘性,并具有非常低的摩擦系数。它干净,不油腻,无污染,
化学惰性,可在260°C(500°F)或更高的温度下工作。
TraSys®715将满足模塑商的生产,环境和安全要求。它提供无与伦比的润滑性和耐用性组合,无需使用硅油,提供一致的释放和减少霉菌堆积。 TraSys®715不含溶剂,符合所有现有和预期的环境法规。此外,TraSys®715不含任何可能形成易燃蒸气的醇类。
用途
TraSys®715是旋转模具内件和其他需要一致控制释放的模塑应用的理想选择。
使用指南
使用前必须搅拌TraSys®715。应将TraSys®715脱模涂料涂于清洁干燥的表面。为获得最佳效果,请在施工前将模具表面预热至55-60°C(130-140°F)。

推荐程序
1.使用玻璃或塑料珠粒介质,研磨垫,清洁溶剂或高pH值清洁剂彻底清洁模具,以去除所有先前的脱模剂
和其他污染源。
2.如果喷涂,请使用提供细雾的喷涂设备。擦拭时,在搅拌后用TraSys®715轻轻擦拭干净的布。搅拌后,轻轻涂抹在模具表面,确保模具的所有区域都完全涂层。
3.建议最低内模温度为132°C(270°F)以固化释放。这可以在应用后通过在整个生产周期中将模具空运行并且炉温在170°C(350°F)下轻松完成。
适当的固化将在模具和涂层之间产生粘合,确保涂层不会转移到第一个模塑部件,并确保最有效的涂层耐用性和循环寿命。
4.当进行点涂处理时,用热风枪固化新涂覆的区域将进一步增强涂层与模具表面之间的粘合。较大的应用可能需要如上所述的烘烤循环。

版权信息

Stoner杜邦TraSys脱模剂TraSys420 TraSys428 TraSys420 TraSys818 TraSys423 TraSys9825 TraSys500 TraSys825TraSys500杜邦脱模剂离型剂